JUSHUO GH125-S04CCA-00
Product Overview
Product Name: WAFER
Description: 1.25mm Pitch wafer patch socket Connectors with latch.
Usage: Suitable for FPC/FFC mating.
Environmental Compliance: Products comply with ROHS environmental requirements.
Brand
JUSHUO ()
Origin
Shenzhen, China
Company Website
jushuo.net.cn
Contact Email
jushuo518@163.com
Company Phone
0755-27220896
| Item | Specification | Requirement |
|---|---|---|
| Rated Voltage (MAX) | 50V | |
| Rated Current (MAX) | [AC/DC (Virtual value) 50Hz] | 1A |
| Ambient temperature Range | (including terminal temperature rise) | -45 +85 |
| Part Name | Model | Material |
|---|---|---|
| Base | GH125-S**CCA-00 | LCP |
| Pin | Phosphor copper | |
| Stator | Phosphor copper |
| Item | Test Condition | Requirement |
|---|---|---|
| Contact Resistance | Plug in the connector and test with a contact resistance meter to measure both terminals of the connector form a closed loop between. | 20 m MAX |
| Insulation Resistance | Plug in the connector and apply 500V DC voltage between the adjacent contacts and between the contacts and the enclosure for 1 minute. | 500M MIN |
| Dielectric Strength | Mate applicable FPC/FFC and apply 200V AC (virtual value) for 1 minute between adjacent terminals or ground. | No Breakdown |
| Pin fixing force | Fix the pin holder on the drawing machine and apply force on the front end of the pin at a rate of 253mm per minute until the pin is withdrawn from the pin holder. (Single pin) | 5N MIN |
| Terminal Retention in Plastic parts | The terminal shall be matched with the hole seat, and at the rate of 253mm per minute along the conductor direction, the force that the terminal is pulled out of the socket. (Single terminal) | 5N MIN |
| Item | Test Condition | Requirement |
|---|---|---|
| Heat Resistance | Place the connector in an environment of +852 for 96H, then take it out and test after 1-2H in normal environment. | Appearance: No Damage; Contact Resistance: 30 m MAX |
| Cold Resistance | Place the connector in an environment of -452 for 96H, then take it out and test after 1-2H in normal environment. | Appearance: No Damage; Contact Resistance: 30 m MAX |
| Humidity | Place the connector in an environment of 452, relative humidity 90-96% for 96H. After the test, take it out and test after 1-2H in normal environment. | Appearance: No Damage; Insulation Resistance: 30 M MIN; Dielectric Strength: 500V AC/MIN |
| Temperature Cycling | Place the test samples in a high and low temperature test chamber and adjust the temperature according to the following steps: a) Hold at -453 for 30 minutes; b) Hold at normal temperature and humidity for 1H; c) Hold at 853 for 30 minutes; d) Hold at normal temperature and humidity for 1H; a) to d) is one cycle, a total of 5 cycles. Recover in normal environment for 2H before inspection. | Appearance: No Damage; Contact Resistance: 60 m MAX |
| Salt Spray Resistance | The test sample is suspended from the top of the test chamber; sprayed with 452, 5 1% salt water for 48 hours; washed with normal temperature water after the test; then dried at room temperature. | Appearance: No Damage, No Corrosion; Contact Resistance: 30 m MAX |
| Solder Ability | Immerse the sample's soldering surface in a 2455 tin bath for 2.50.5 sec. (0.2 mm from terminal tip) | Tin Area: Above 95%; Appearance: No Damage |
| Soldering Resistance | Place the connector on a PCB board and immerse it in a 2605 tin bath for 50.5 sec. (0.2 mm from terminal tip) | Tin Area: Above 95%; Appearance: No Damage, No Deformation |
| Item | Appearance | Size |
|---|---|---|
| The surface of plastic parts shall be free of obvious scars, mottled, cracked, burr, flash, lack of material and deformation affecting the use; the surface of metal parts shall be smooth and clean, no rust, oxidation, peeling, blackening and obvious mechanical damage. | Reference engineering drawing |
HRS DF56C-26S-0.3V(51)
Product InformationThis document appears to be a label or part of a manual for a product. The text is largely unreadable due to image quality or formatting. No specific product overview, advantages, or application scenarios can be extracted.Part NumberModelDateSIU3PUOCSIL0IMOPUIM SI(BS N0 121032023...
HRS DF36A-25S-0.4V(51)
Product OverviewThe DF36 Series is a 0.4mm pitch, vertical mating, micro-coaxial cable connector designed for high-density applications. It offers a reliable connection solution for micro-coaxial cables, featuring space-saving configurations suitable for modern electronic devices.Brand: Hirose ...
HRS DF56C-30S-0.3V(51)
Product OverviewThe provided text appears to be a scanned document with OCR errors and does not contain clear product information such as function, usage, advantages, or application scenarios. Therefore, this section cannot be populated.AttributeValueProduct NameSIU3PUOCSIL0I MOPUIM SIS N0 ...
HRS DF56-50S-0.3V(51)
Product OverviewThe provided text does not contain clear information about product overview, function, usage, advantages, or application scenarios. It appears to be garbled or incomplete technical data.Part NumberDescriptionUnit PriceSJU3PUOCSIL0IMOPUIM SI(BS N0 12103 Ajpuny AUpigena) YSIy PUBLIP ...
