PANASONIC AXK500137YG
Product Overview
These narrow pitch connectors are designed for board-to-board and board-to-FPC applications. They are intended to be used within specified electrical and environmental conditions to prevent damage such as abnormal heating, smoke, or fire. Panasonic Corporation emphasizes thorough specification review and offers support for usages outside standard specifications. Continuous improvement in quality and reliability is a focus, but users are advised to check actual component performance in their specific use environments. Safety designs, including redundancy, fire spread prevention, and malfunction prevention, are recommended to mitigate risks associated with component failure or end-of-life.
When using board-to-board connectors, avoid connecting a pair of boards with multiple connectors to prevent mating failures or product breakage due to misalignment. PC board patterns should be designed considering the performance of mounting equipment, with potential errors of 0.2 to 0.3 mm in positioning. Connectors with positioning tabs require corresponding positioning holes on the PC board. Mechanical strength during soldering is ensured by adhering to recommended PC board pattern design dimensions. For connectors without stand-offs, minimize cover lay thickness to prevent poor soldering. To prevent PC boards from detaching under vibration or impact, and to avoid direct loads on soldered portions, secure the PC board in place using methods like screws. Measures should also be taken to prevent the connector from coming off when connecting PC boards.
When mounting connectors on an FPC, reinforcing plates are recommended on the backside of the FPC to prevent solder detachment from terminals during mating and unmating. The reinforcing plate should be larger than the recommended PC board pattern dimensions. For connectors with temporary locking structures, consider measures to prevent mating separation due to dropping impact, especially with FPCs of significant size, weight, or bending force. The compact and thin design of narrow pitch connectors requires care during mating to prevent damage or deformation from displacement or angled mating.
Brand
Panasonic Corporation
Application
Board-to-board / Board-to-FPC
Safety Remarks
Observe safety remarks to prevent accidents and injuries. Do not use beyond specification sheets. Review specifications thoroughly. Contact sales representative for out-of-spec usage. Panasonic Corporation cannot guarantee quality and reliability for out-of-spec usage.
PC Board Pattern Design
Design PC boards and patterns considering equipment positioning accuracy (0.2-0.3 mm error). Use positioning holes for connectors with tabs. Meet recommended PC board pattern design dimensions for mechanical strength. Minimize cover lay thickness to prevent poor soldering. Secure PC boards to prevent detachment during vibrations or impacts.
FPC Mounting Considerations
Attach reinforcing plate to FPC backside to prevent solder detachment. Consider measures to prevent mating separation due to dropping impact for temporary locking connectors.
Connector Handling
Take care when mating narrow pitch connectors to prevent damage or deformation from displacement or angled mating.
| Item | Specifications | Conditions |
| Rated current | 0.5 A/pin contact (Max. 10 A at total pin contacts) | |
| Rated voltage | 60 VAC/DC | |
| Dielectric strength | 150 V AC for 1 min. | No short-circuiting or damage at a detection current of 1 mA when the specified voltage is applied for one minute. |
| Insulation resistance | Min. 1000 M (initial) | Using 500 V DC megger (applied for 1 min.) |
| Contact resistance | Max. 60 m | Based on the contact resistance measurement method specified by JIS C 5402. |
| Composite insertion force | Max. 0.785 N/pin contact x pin contacts (initial) | |
| Composite removal force | Min. 0.0588 N/pin contact x pin contacts | |
| Ambient temperature | -55 to +85C | No icing. No condensation. |
| Soldering heat resistance | Reflow soldering: Peak temperature: 260C or less; Soldering iron: 300C within 5 sec. / 350C within 3 sec. | The initial specification must be satisfied electrically and mechanically. (on the surface of the PC board around the connector terminals) |
| Storage temperature | -55 to +85C (product only) / -40 to +50C (emboss packing) | No icing. No condensation. |
| Thermal shock | 5 cycles, insulation resistance Min. 100 M, contact resistance Max. 60 m | Conformed to MIL-STD-202F, method 107G. Temperature profile: -55C (30 min) -> Max. 5C (5 min) -> +85C (30 min) -> Max. 5C (5 min). 5 cycles. |
| Humidity resistance | Insulation resistance Min. 100 M, contact resistance Max. 60 m | Conformed to IEC60068-2-78. Temperature 402C, humidity 90 to 95% RH, 120 hours. |
| Saltwater spray resistance | Insulation resistance Min. 100 M, contact resistance Max. 60 m | Conformed to IEC60068-2-11. Temperature 352C, saltwater concentration 51%, 24 hours. |
| HS resistance | Contact resistance Max. 60 m | Temperature 402C, gas concentration 31 ppm, humidity 75 to 80% RH, 48 hours. |
| Lifetime characteristics | Insertion and removal life Max. 50 times / Repeated insertion and removal speed of 200 times/hour |
| Product | Mated height | Rated current (Max. total pin) | Unit weight (50 pins) |
| P5K | 3.0 mm | Max. 10 A | Socket: 0.17 g, Header: 0.09 g |
| P5KS | 4.0 mm | Max. 16 A | Socket: 0.18 g, Header: 0.16 g (30 pins) |
| P5KS | 4.5 mm | Max. 16 A | |
| P5KS | 5.0 mm | Max. 16 A | |
| P5KS | 5.5 mm | Max. 16 A | |
| P5KS | 6.0 mm | Max. 16 A | |
| P5KS | 6.5 mm | Max. 16 A | |
| P5KS | 7.0 mm | Max. 16 A | |
| P5KS | 8.0 mm | Max. 16 A | |
| P5KS | 9.0 mm | Max. 16 A |
| Part name | Material | Surface treatment |
| Molded portion | LCP resin (UL94V-0) | |
| Contact and Post | Copper alloy | Contact portion: Base: Ni plating Surface: Au plating. Terminal portion: Base: Ni plating Surface: Au plating (except the terminal tips). Terminals close to soldering portion have nickel barriers. |