SHETIME WAF02-T1T1-2021-D
Product Overview
This document outlines the technical specifications and test procedures for a connector, focusing on its performance under various environmental and mechanical conditions. It details requirements for durability, contact resistance, vibration resistance, thermal aging, insulation resistance, mechanical strength, temperature rise, humidity resistance, and temperature cycling.
Technical Specifications
| Item | Test Mode | Requirement | Measurement |
|---|---|---|---|
| Durability | Mate connectors up to 30 cycles at a maximum rate of 10 cycles per minute prior to environmental test | - | - |
| Contact Resistance | - | <30m | <30m |
| Vibration | Frequency: 10-55-10 Hz/minute Amplitude: 1.5mm p-p Direction: 3 axes (up/down, left/right, front/back) Period: 2 hours for each direction | Appearance: No damage Contact Resistance: <30m Current Discontinuity: Max 1 microsecond | - |
| Thermal Aging | Temperature: 85 2 C Period: 96 hours continuously | Appearance: No damage Contact Resistance: <30m | - |
| Insulation Resistance | Apply 500V DC (rms) for 1 minute between adjacent contacts | >100 M | - |
| Terminal crimping wire strength (AWG#28 wire) | Axial pullout force at a rate of 25 3mm per minute | >13N | - |
| Terminal crimping wire strength (AWG#30 wire) | Axial pullout force at a rate of 25 3mm per minute | >8N | - |
| Terminal crimping wire strength (AWG#32 wire) | Axial pullout force at a rate of 25 3mm per minute | >6N | - |
| Fixed terminals and hole seat | Pull out from the hole in the seat capacity at a rate of 25 3mm per minute along the wire direction | Per contact: >8N | - |
| Single contact insertion force | Housing with terminal ends matched with wafer, inserting force test at a rate of 25 3mm per minute | <2N | - |
| Single contact withdrawal force | Housing with terminal ends matched with wafer, pull-out test at a rate of 25 3mm per minute | >0.2N | - |
| Pin Retention force | Force on pin end until needle exits seat, pull-out force at a rate of 25 3mm per minute | Per contact: >3N | - |
| Temperature Rise | Mate connector measured at maximum rated current | 5L | - |
| Humidity | Constant temperature and humidity (40 2 C, 90-95% RH) for 96 hours continuously | Appearance: No damage Contact Resistance: <30m Insulation Resistance: 50M Withstand Voltage: No breakdown or flashover | - |
| Temperature Cycling | One cycle: -553C (30min) -> Room temp. (10-15 min) -> 853C (30min) -> Room temp. (10-15 min). Total 5 cycles. | Same as paragraph 8.3 (Contact Resistance, Insulation Resistance, Withstand Voltage) | - |
HRS DF56C-26S-0.3V(51)
Product InformationThis document appears to be a label or part of a manual for a product. The text is largely unreadable due to image quality or formatting. No specific product overview, advantages, or application scenarios can be extracted.Part NumberModelDateSIU3PUOCSIL0IMOPUIM SI(BS N0 121032023...
HRS DF36A-25S-0.4V(51)
Product OverviewThe DF36 Series is a 0.4mm pitch, vertical mating, micro-coaxial cable connector designed for high-density applications. It offers a reliable connection solution for micro-coaxial cables, featuring space-saving configurations suitable for modern electronic devices.Brand: Hirose ...
HRS DF56C-30S-0.3V(51)
Product OverviewThe provided text appears to be a scanned document with OCR errors and does not contain clear product information such as function, usage, advantages, or application scenarios. Therefore, this section cannot be populated.AttributeValueProduct NameSIU3PUOCSIL0I MOPUIM SIS N0 ...
HRS DF56-50S-0.3V(51)
Product OverviewThe provided text does not contain clear information about product overview, function, usage, advantages, or application scenarios. It appears to be garbled or incomplete technical data.Part NumberDescriptionUnit PriceSJU3PUOCSIL0IMOPUIM SI(BS N0 12103 Ajpuny AUpigena) YSIy PUBLIP ...
