JUSHUO GH125-S03DCA-00
Product Overview
Product Name: 1.25mm (1.25mm Horizontal Surface Mount Connector with Latch)
Product Model: GH125-S**DCA-00
Scope of Application: This specification is applicable to GH series products.
Brand
SHENZHEN JUSHUO ELECTRONIC CO.,LTD
Origin
China
Certifications
ROHS
Package Type
Inner packing: joint and several, Outer packing: carton. Sealed in the box, do not shake.
| Item | Specification | Unit | Requirement |
|---|---|---|---|
| Rated Voltage | 50 | V | AC/DC |
| Rated Current | 1.0 | A | AC/DC |
| Operating Temperature Range | -25 to 85 | ||
| Operating Humidity Range | Below 90% | Relative Humidity |
| Part Name | Model | Material |
|---|---|---|
| Base | GH | LCP E130i |
| Pin | GH | Phosphor copper |
| Stator | GH | Phosphor copper |
| Project | Test Method | Performance Requirement | |
|---|---|---|---|
| Contact Resistance | Tested with a contact resistance meter after plugging in the connector. Measures resistance between two terminals forming a closed loop. | 20 | m Max |
| Insulation Resistance | Plug in the connector and apply 100V DC voltage between adjacent contacts and between contacts and enclosure for 1 minute. | 500 | M Min |
| Withstand Voltage | Plug in the connector and apply 500V AC voltage between adjacent contacts and between contacts and enclosure for 1 minute. | No breakdown and flashover |
| Project | Test Method | Performance Requirement | |
|---|---|---|---|
| Heating Test | Place the plugged-in connector in an environment of +852 for 96H. Take out and place in normal environment for 1-2H before testing. | Appearance: No damage Contact Resistance: 60 m Max | |
| Cold Tolerance Test | Place the plugged-in connector in an environment of -252 for 96H. Take out and place in normal environment for 1-2H before testing. | Appearance: No damage Contact Resistance: 60 m Max | |
| Moisture Resistance Test | Place the plugged-in connector in an environment of 402, 90-96% relative humidity for 96H. After the test, take it out and place in normal environment for 1-2H before testing. | Appearance: No damage Insulation Resistance: 60 M Min Withstand Voltage: 250V AC/minute MIN | |
| Temperature Cycle | Place test samples in high and low temperature test chamber. Steps: a. -253 for 30 min; b. Room temperature for 1H; c. +853 for 30 min; d. Room temperature for 1H. Repeat 5 cycles. Recover in normal environment for 2H before inspection. | Appearance: No abnormalities Contact Resistance: 60 m Max | |
| Salt Spray Test | Suspend test samples in test box. Continuous spray with (51)% NaCl solution for 24H. After testing, gently wash surface precipitates with flowing distilled water. Recover at normal temperature for 1-2H before inspection and measurement. | Appearance: No damage or corrosion (Hardware should not have serious corrosion exposing base metal. Pre-plated profiles are allowed slight corrosion on blanking surface that does not affect performance.) Contact Resistance: 60 m Max | |
| Weldability | Dip the part to be welded of the test sample into 2605 tin solution for 2.50.5 seconds. | Tin coverage area: Above 95% | |
| Soldering Resistance | Place the connector on a PCB board, then test by reflow soldering or wave soldering at 2605 for 51S. | 1. Plastic parts shall be free from obvious deformation, damage, and blistering. 2. Electrical characteristics must meet specifications. |
| Project | Test Method | Performance Requirement | |
|---|---|---|---|
| Pin Fixing Force | Fix the pin holder on the drawing machine and apply force on the pin front end at a rate of 253mm/min until the pin is withdrawn from the pin holder. | Single pin: 5 N Min | |
| Terminal Retention in Plastic Parts | The terminal shall be matched with the hole seat, and at a rate of 253mm/min along the conductor direction, the force to pull the terminal out of the socket. | Single terminal: 7 N Min | |
| Mechanical Life | Under no power on state, plug and unplug 30 times at a speed of 10 times/min. | Contact Resistance: 80 m Max | |
| Terminal Crimp Lead Line Strength | The terminals are crimped into wire and pulled axially at a rate of 253mm/min. | 26AWG wire: 17.8N 28AWG wire: 8.9N 30AWG wire: 4.4N 32AWG wire: 2.2N | |
| Insertion/Pull-out Force | (1) Fit the hole seat and terminal, conduct insertion and removal test on the same axis with the needle seat. Remove the lock of the hole seat (test speed: 205mm/min). (2) Performance Requirements: | Insertion force: 2N (Per pin) Pull-out force: 0.3N (Per pin) |
HRS DF56C-26S-0.3V(51)
Product InformationThis document appears to be a label or part of a manual for a product. The text is largely unreadable due to image quality or formatting. No specific product overview, advantages, or application scenarios can be extracted.Part NumberModelDateSIU3PUOCSIL0IMOPUIM SI(BS N0 121032023...
HRS DF36A-25S-0.4V(51)
Product OverviewThe DF36 Series is a 0.4mm pitch, vertical mating, micro-coaxial cable connector designed for high-density applications. It offers a reliable connection solution for micro-coaxial cables, featuring space-saving configurations suitable for modern electronic devices.Brand: Hirose ...
HRS DF56C-30S-0.3V(51)
Product OverviewThe provided text appears to be a scanned document with OCR errors and does not contain clear product information such as function, usage, advantages, or application scenarios. Therefore, this section cannot be populated.AttributeValueProduct NameSIU3PUOCSIL0I MOPUIM SIS N0 ...
HRS DF56-50S-0.3V(51)
Product OverviewThe provided text does not contain clear information about product overview, function, usage, advantages, or application scenarios. It appears to be garbled or incomplete technical data.Part NumberDescriptionUnit PriceSJU3PUOCSIL0IMOPUIM SI(BS N0 12103 Ajpuny AUpigena) YSIy PUBLIP ...
