SHETIME WAFP3-T1T1-2020-D
Product Overview
This product undergoes various tests to ensure its durability, performance, and reliability under different environmental and mechanical conditions. Key tests include Durability, Contact Resistance, Vibration, Thermal Aging, Insulation Resistance, Mechanical Performance (Terminal crimping, Fixed terminals, Insertion/Withdrawal force, Pin Retention), Temperature Rise, Humidity, and Temperature Cycling.
| Item | Test Mode | Requirement | Test Details | Result |
|---|---|---|---|---|
| Durability | Mate connectors up to 30 cycles at a maximum rate of 10 cycles per minute prior to environmental test | N/A | N/A | N/A |
| Contact Resistance | N/A | <30m | Hfpt A <30m | N/A |
| Vibration | Connector combination state of the welding circuit board as test samples, resistance to vibration test | Discontinuous current (off) phenomenon, after the experiment contact resistance | Frequency: 10-55-10 Hz/minute (35%) Amplitude: 1.5mm p-p (#& &) Direction: Axis of up and down, right to left, front and back (J7 [A]) Period: 2 hours for each direction (/& #) | Appearance: No damage Contact Resistance: <30m Current Discontinuity: 1 micro second Max (BIR AW 1 usec Max) |
| Thermal Aging | Connector combination condition is placed in the oven, high temperature aging test | Appearance: No damage Contact Resistance: <30m | Temperature: 852C Period: 96 hours continuously (W 8522 C, A FEE 96 /T) | N/A |
| Insulation Resistance | Apply 500V DC (rms) for 1 minute between adjacent contacts | >100 M (Z100MQ) | FAATPIHE AR K, 1 R RN REF 500V DC H & ER LG ERE | N/A |
| Terminal crimping wire strength | AWG#28 wire: Pullout force | >13N (13N) | AWGH28 wire, 253mm rate per minute axial pullout force | N/A |
| Terminal crimping wire strength | AWG#30 wire: Pullout force | >8N (8N) | AWGH#H30 wire, 253mm rate per minute axial pullout force | N/A |
| Terminal crimping wire strength | AWG#32 wire: Pullout force | >6N (6N) | AWGH32 wire, 253mm rate per minute axial pullout force | N/A |
| Fixed terminals and hole seat | Terminal and hole seat pull out force | >8N (8N) per contact | Terminal and hole seat, 253mm rate per minute along the wire direction pulled out from the hole in the seat capacity | N/A |
| Single contact insertion force | Housing with terminal ends matched with wafer, inserting force test | <2N (2N) | Housing with terminal ends, 253mm rate per minute insertion force test | N/A |
| Single contact withdrawal force | Housing with terminal ends matched with wafer, pull-out test | >0.2N (0.2N) | Housing with terminal ends, 253mm rate per minute pull-out test | N/A |
| Pin Retention force | Force on pin end | >3N (3N) per contact | Exerts a force on the pin end, 253mm rate per minute until the needle exit seat pull-out force | N/A |
| Temperature Rise | Mate connector measure temperature rise | 5L | When the maximum rated current is passed | N/A |
| Humidity | Connector combination under constant temperature and humidity | Appearance: No damage Contact Resistance: <30m Insulation Resistance: 50M (50MQ) Withstand Voltage: No breakdown or flashover | Temperature: 402C Relative humidity: 90-95%RH Period: 96 hours continuously (RE40+2C, S :90-95%, JEHA: FrEE 96 /N) | N/A |
| Temperature cycling | Thermal shock test | Same as paragraph 8.3 | One cycle consists of: -553C (30min), Room temp. (10-15 min), 853C (30min), Room temp. (10-15 min). Total cycle: 5 cycles. (-55+3C,30 %k, FERRETE 10-15 o4, 85+3C,30 43pl, FUEHIATE 10-15 455, TERR S 5K) | N/A |