SHETIME WAFP7-T1T1-2021-D
Product Overview
The provided text describes various test modes and requirements for connector performance, including Durability, Contact Resistance, Vibration, Thermal Aging, Insulation Resistance, Mechanical Performance (Terminal crimping wire strength, Fixed terminals and hole seat, Single contact insertion/withdrawal force, Pin Retention force), Temperature Rise, Humidity, and Temperature Cycling. These tests ensure the reliability and performance of the connectors under different environmental and operational conditions.
Technical Specifications
| Item | Test Mode | Requirement | Details | |
|---|---|---|---|---|
| Durability | Mate connectors | 30 cycles at a Maximum rate of 10 cycles per minute prior to environmental test | - | |
| Contact Resistance | - | <30m | Hfpt A <30m | |
| Vibration | Connector combination state of the welding circuit board | Resistance to vibration test, whether to produce discontinuous current (off) | Frequency: 10-55-10 Hz/minute Amplitude: 1.5mm p-p Direction: Axis of up and down, right the left, front and back Period: 2 hours for each direction G MrREg: 2 /iy | |
| Vibration | - | Appearance: No damage | - | |
| Vibration | - | Contact Resistance: <30m | Bl <30 m | |
| Vibration | - | Current Discontinuity: 1 micro second Max | BIR AW 1 usec Max | |
| Thermal Aging | Connector combination condition placed in the oven | High temperature aging test, after the test and measurement of contact resistance | Temperature: 85+ 2 C Period: 96 hours continuously | |
| Thermal Aging | - | Appearance: No damage | ShAL: AR | |
| Thermal Aging | - | Contact Resistance: <30m | FEAHE<30m | |
| Temperature Rise | Mate connector | Measure the temperature rise of contact when the maximum rated current is passed | 5L | |
| Humidity | Connector combination under constant temperature and humidity | Constant temperature and humidity test, after experiment measuring contact resistance, insulation resistance, and withstand voltage test | Temperature: 40 2 C Relative humidity: 90-95%RH Period: 96 hours continuously | |
| Humidity | - | Appearance: No damage | Sh: T | |
| Humidity | - | Contact Resistance: <30m | B <30m | |
| Humidity | - | Insulation Resistance: 50M | HLHEIE: =50MQ | |
| Humidity | - | Withstand Voltage | No breakdown or flashover | Tt T A |
| Temperature Cycling | Combined state of connectors | Thermal shock test, after the test measuring contact resistance, insulation resistance, and resistance to voltage | One cycle consists of: -55+3C, 30min, Room temp. 10-15 min 85 +3C, 30min, Room temp. 10-15 min Total cycle: 5 cycle | |
| Temperature Cycling | - | Same as paragraph 8.3 | M 8.3 & |
| Item | Test Mode | Requirement | Details |
|---|---|---|---|
| Insulation Resistance | Apply 500V DC(rms) for 1 minute between adjacent contacts | More than 100 M | Z100MQ |
| Terminal crimping wire strength | AWG#28 wire | Axial pullout force: More than 13N | 213N |
| Terminal crimping wire strength | AWG#30 wire | Axial pullout force: More than 8N | =8N |
| Terminal crimping wire strength | AWG#32 wire | Axial pullout force: More than 6N | =Z6N |
| Fixed terminals and hole seat | Pullout force along the wire direction | Per contact: More than 8N | =8N |
| Single contact insertion force | Housing together with terminal ends matched with Wafer | Less than 2N | =2N |
| Single contact withdrawal force | Housing together with terminal ends matched with Wafer | More than 0.2N | =20.2N |
| Pin Retention force | Exerts a force on the pin end | Per contact: More than 3N | 23N |