SHETIME WAF06-T1T1-2021-D
Product Overview
This document outlines the testing procedures and requirements for connector performance, covering durability, electrical characteristics, mechanical strength, and environmental resistance. These tests ensure the reliability and longevity of the connectors under various operating conditions.
Application Scenarios
The connectors are designed for applications requiring high reliability and robust performance, including but not limited to industrial automation, automotive electronics, and telecommunications equipment.
Brand
N/A
Origin
N/A
Material
N/A
Color
N/A
Certifications
N/A
Package Types
N/A
Technical Specifications
| Test Item | Test Mode | Requirement | Details |
|---|---|---|---|
| Durability | Mate connectors up to 30 cycles at a maximum rate of 10 cycles per minute prior to environmental test | N/A | N/A |
| Contact Resistance | Hfpt A | <30m | N/A |
| Vibration | PR3 | N/A | Frequency: 10-55-10 Hz/minute (35%) Amplitude: 1.5mm p-p (#& &) Direction: Axis of up and down, right to left, front and back Period: 2 hours for each direction |
| Appearance (Vibration) | N/A | No damage | N/A |
| Contact Resistance (Vibration) | N/A | <30m | N/A |
| Current Discontinuity (Vibration) | N/A | Max 1 microsecond | N/A |
| Thermal Aging | i 1 iR | N/A | Temperature: 85 2 C Period: 96 hours continuously |
| Appearance (Thermal Aging) | N/A | No damage | N/A |
| Contact Resistance (Thermal Aging) | N/A | <30m | N/A |
| Insulation Resistance | 2z FfH | >100 M | Apply 500V DC (rms) for 1 minute between adjacent contacts |
| Terminal Crimping Wire Strength (AWG#28) | S B SR | >13N | Axial pullout force at a rate of 25 3mm per minute |
| Terminal Crimping Wire Strength (AWG#30) | S B SR | >8N | Axial pullout force at a rate of 25 3mm per minute |
| Terminal Crimping Wire Strength (AWG#32) | S B SR | >6N | Axial pullout force at a rate of 25 3mm per minute |
| Fixed Terminals and Hole Seat | ST 5 FLIEIE 5 | >8N per contact | Pull out force at a rate of 25 3mm along wire direction |
| Single Contact Insertion Force | RN S | <2N | Housing with terminal ends matched with wafer, inserting force test at a rate of 25 3mm per minute |
| Single Contact Withdrawal Force | AR ) | >0.2N | Housing with terminal ends matched with wafer, pull-out test at a rate of 25 3mm per minute |
| Pin Retention Force | PIN [l 52 | >3N per contact | Force on pin end until needle exits seat, pull-out force at a rate of 25 3mm per minute |
| Temperature Rise | B | 5L | Measure temperature rise of contact when maximum rated current is passed |
| Humidity | {5 #IE | N/A | Temperature: 40 2 C Relative humidity: 90-95% RH Period: 96 hours continuously |
| Appearance (Humidity) | N/A | No damage | N/A |
| Contact Resistance (Humidity) | N/A | <30m | N/A |
| Insulation Resistance (Humidity) | N/A | 50M | N/A |
| Withstand Voltage (Humidity) | N/A | No breakdown or flashover | N/A |
| Temperature Cycling | R PETRE | Same as paragraph 8.3 | One cycle: -55+3C (30min), Room temp. (10-15 min), 85+3C (30min), Room temp. (10-15 min). Total cycle: 5 cycles. |
| Contact Resistance (Temp. Cycling) | M 8.3 & | <30m | N/A |
| Insulation Resistance (Temp. Cycling) | M 8.3 & | <30m | N/A |
| Withstand Voltage (Temp. Cycling) | M 8.3 & | No breakdown or flashover | N/A |