JUSHUO GH125-S02DCA-00
Product Overview
Product Name: 1.25mm(
Product Model: GH125-S**DCA-00
Description: This product specification applies to the GH series products.
Application Scenarios: Applicable to GH series products.
Brand
SHENZHEN JUSHUO ELECTRONIC CO.,LTD
Origin
China (implied by company address)
Certifications
ROHS environmental protection requirements
Package Type
Inner packing: joint and several; Outer packing: carton. Product sealed in box, do not shake.
| Item | Specification | Unit |
|---|---|---|
| Rated Voltage | 50 | V AC/DC |
| Rated Current | 1.0 | A |
| Operating Temperature Range | -25 to 85 | |
| Operating Humidity Range | Below 90% | Relative Humidity |
| Storage Temperature Range | -20 to 50 | |
| Storage Humidity Range | Not more than 90% | Relative Humidity |
| Transport Temperature Range | -20 to 50 |
| Part Name | Model | Material |
|---|---|---|
| Base | GH | LCP E130i |
| Pin | GH | Phosphor copper |
| Stator | GH | Phosphor copper |
| Item | Test Method | Performance Requirement |
|---|---|---|
| Contact Resistance | Plug in the connector and test with a contact resistance meter. | 20 m Max |
| Insulation Resistance | Apply 100V DC voltage between adjacent contacts and between contacts and enclosure for 1 minute. | 500 M Min |
| Withstand Voltage | Apply 500V AC voltage between adjacent contacts and between contacts and enclosure for 1 minute. | No breakdown and flashover |
| Item | Test Method | Performance Requirement |
|---|---|---|
| Heating Test | Place plug connector in +852 environment for 96H, then in normal environment for 1-2H. | Appearance: No damage. Contact Resistance: 60m Max. |
| Cold Tolerance Test | Place plug connector in -252 environment for 96H, then in normal environment for 1-2H. | Appearance: No damage. Contact Resistance: 60m Max. |
| Moisture Resistance Test | Place plug connector in 402, 90-96% RH environment for 96H, then in normal environment for 1-2H. | Appearance: No damage. Insulation Resistance: 60M Min. Withstand Voltage: 250V AC/min ute MIN. |
| Temperature Cycle | 5 cycles: -253 (30min) -> Room Temp (1H) -> +853 (30min) -> Room Temp (1H). Recover 2H. | Appearance: No abnormalities. Contact Resistance: 60m Max. |
| Salt Spray Test | Continuous spray with 5%1% NaCl solution for 24H. Wash with distilled water, recover 1-2H. | Appearance: No damage or corrosion. Contact Resistance: 60m Max. |
| Weldability | Dip in 2605 tin solution for 2.50.5 seconds. | Tin coverage area: 95% or more. |
| Soldering Resistance | Place connector on PCB, reflow or wave solder at 2605 for 51S. | 1. Plastic parts: No obvious deformation, damage, blistering. 2. Electrical characteristics must meet specifications. |
| Item | Test Method | Performance Requirement |
|---|---|---|
| Pin Fixing Force | Fix pin holder, apply force at 253mm/min until pin withdraws. | Single pin: 5N Min |
| Terminal Retention in Plastic Parts | Pull terminal out of socket at 253mm/min along conductor direction. | Single terminal: 7N Min |
| Mechanical Life | Plug and unplug 30 times at 10 times/min without power. | Contact Resistance: 80m Max. |
| Terminal Crimp Wire Strength | Axial pullout force at 253mm/min. | 26AWG wire: 17.8N. 28AWG wire: 8.9N. 30AWG wire: 4.4N. 32AWG wire: 2.2N. |
| Insertion/Pull-out Force | Fit socket and terminal, test insertion/removal on the same axis (remove socket lock). Test speed: 205mm/min. | Insertion Force: 2N (Per pin). Pull-out Force: 0.3N (Per pin). |